SAE AMS4152 Aluminum Alloy Extrusions 4.4Cu - 1.5Mg - 0.60Mn (2024-T3) Solution Heat Treated

作者:标准资料网时间:2024-05-11 02:16:24 浏览:8041 来源:标准资料网

Product Code:SAE AMS4152
Title:Aluminum Alloy Extrusions 4.4Cu - 1.5Mg - 0.60Mn (2024-T3) Solution Heat Treated
Issuing Committee:Ams D Nonferrous Alloys Committee
Scope: This specification covers an aluminum alloy in the form of extruded bars, rods, wire, shapes, and tubing.
Rationale: This specification covers an aluminum alloy in the form of extruded bars, rods, wire, shapes, and tubing.

下载地址: 点击此处下载

返回跳至顶部

上一篇: SAE AMS4094 Aluminum Alloy, Sheet and Plate, Alclad 6.3cu 0.30mn 0.18zr 0.10v 0.06ti Alclad 2219-T81 Sheet Solution Heat
下一篇: SAE AMS4236 Aluminum Alloy Castings, 4.6Cu - 0.35Mn - 0.25Mg - 0.22Ti (A206.0-T4), Solution Heat Treated and Naturally A

Product Code:SAE J1996
Title:Internal Combustion Engines--Piston Rings--Quality Requirements (Cancelled Jun 2008)
Issuing Committee:Piston And Ring Standards Committee
Scope: This SAE Standard specifies the quality aspects that are capable of definition but not normally found on a drawing specification. The difficulty of trying to define in absolute terms the quality attainable in normal commercial manufacture of piston rings is well known. In this document the commonly encountered aspects of quality in terms of casting defects and other departures from ideal are quantified. Many minor defects are clearly quite acceptable; other defects because of size or numbers are inadmissible. This document covers the following: a) Single piece piston rings of grey, carbidic, malleable, spheroidal graphite cast iron or steel; b) Multipiece pistong rings (oil control rings) consisting of cast iron parts and spring components; c) Single piece and multipiece rings of steel, i.e., oil control rings in the form of strip steel components or steel segments (rails) with spring expander components. In addition to specifying certain limits fo acceptance relating to inspection measuring principles (covered by SAE J1589) this document also covers those features for which no recognized quantitative measurement procedures exist and which are only checked visually with normal eyesight and without magnification. Such features (superficial defects) are additional to the standard tolerances of ring width, radial wall thickness, and closed gap. The requirements of this document apply to all rings up to and including 200 mm diameter covered by the above classification for both reciprocating internal combustion engines and compressors.【英文标准名称】:CommonNameforthePestControlChemical2-Chloro-N-(((4-methoxy-6-methyl-1,3,5-triazin-2-yl)amino)carbonyl)benezenesulfonamide"Chlorsulfuron"
【原文标准名称】:绿黄隆(chlorsulfuron)－(除草剂)通用名称
【标准号】:ANSIK62.249-1981
【标准状态】:作废
【国别】:美国
【发布日期】:1981
【实施或试行日期】:
【发布单位】:美国国家标准学会(ANSI)
【起草单位】:ANSI
【标准类型】:()
【标准水平】:()
【中文主题词】:农药
【英文主题词】:Pesticides
【摘要】:
【中国标准分类号】:G25
【国际标准分类号】:65_100_99
【页数】:2P;A4
【正文语种】:英语