SAE AMS5662 Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 52.5ni 19cr 3.0mo 5.1cb 0.90ti 0.50al
作者:标准资料网 时间:2024-05-09 14:01:50 浏览:9167
来源:标准资料网
Product Code:SAE AMS5662
Title:Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 52.5ni 19cr 3.0mo 5.1cb 0.90ti 0.50al 18fe, Consumable Electrode Or Vacuum Induction Melted 1775Mdf (968Mdc) Solution Heat Treated, Precipitation Hardenable
Issuing Committee:Ams F Corrosion Heat Resistant Alloys Committee
Scope:This specification covers a corrosion and heat resistant nickel alloy in the form of bars, forgings, flash welded rings, and stock for forging flash welded rings or heading.
基本信息
| 标准名称： | 配套床上用品 |
| 英文名称： | Matched bedding |
| 中标分类： |
纺织 >>
纺织制品 >>
纺织复制品 |
| ICS分类： |
家用和商用设备、文娱、体育 >>
家用织物、亚麻织物
|
| 发布部门： | 中华人民共和国国家质量监督检验检疫总局 中国国家标准化管理委员会 |
| 发布日期： | 2009-04-21 |
| 实施日期： | 2009-12-01 |
| 首发日期： | 2009-04-21 |
| 作废日期： | |
| 主管部门： | 中国纺织工业协会 |
| 提出单位： | 中国纺织工业协会 |
| 归口单位： | 中国纺织工业协会 |
| 起草单位： | 江苏省纺织产品质量监督检验测试中心、江苏梦兰集团有限公司、江苏堂皇集团等 |
| 起草人： | 葛利利、钱月宝、荆玉堂、金绍伟、李辉 |
| 出版社： | 中国标准出版社 |
| 出版日期： | 2009-12-01 |
| 页数： | 8页 |
| 计划单号： | 20074156-T-608 |
适用范围
本标准规定了配套床上用品的质量要求、抽样、试验方法、标志、包装。本标准适用于以纺织原料为主的配套床上用品。
前言
没有内容
目录
没有内容
引用标准
下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件,其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准,然而,鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件,其最新版本适用于本标准。
GB/T250 纺织品 色牢度试验 评定变色用灰色样卡(GB/T250-2008,ISO105/A02:1993,IDT)
GB5296.4 消费品使用说明 纺织品和服装使用说明
GB18383 絮用纤维制品通用技术要求
GB18401 国家纺织产品基本安全技术规范
GB/T22796 被、被套
GB/T22797 床单
GB/T22843 枕、垫类产品
所属分类： 纺织 纺织制品 纺织复制品 家用和商用设备 文娱 体育 家用织物 亚麻织物
Product Code:SAE J2806
Title:Off-Vehicle Brake Testing for Service Brakes over 10 000 lb GVW--Air, Hydraulic, and Mechanical Actuation
Issuing Committee:Truck And Bus Brake Systems Committee
Scope:Subject document is specifically intended for service brakes and service brakes when used for parking and/or emergencybrakes (only) that are commonly used for automotive-type, ground wheeled vehicles exceeding 4536 kg (10 000 US lb)Gross Vehicle Weight Rating (GVWR). Subject specification provides the off-vehicle procedures, methods, and processesused to objectively determine suitability of tactical and combat ground wheeled vehicle brake systems and selectedsecondary-item brake components (a.k.a. aftermarket or spare parts), including brake “block” for commercial applicationsonly, specifically identified within subject document. Subject specification is primarily based on known industry andmilitary test standards utilizing brake inertia dynamometers. Targeted vehicles and components include, but may not belimited to the following:a. Civilian, commercial, military, and militarized-commercial ground wheeled vehicles such cargo trucks, vocationalvehicles, truck tractors, trailers, specialized support and engineering equipment under the generic heading of GroundVehicle “Dry” Brake Systems (GVDBS).b. Hydraulic, air, and mechanical “dry” disc brake and drum brake systems when used as service brakes, includingservice brakes (only) when used as emergency and/or parking brakes.c. Hydraulic, air, and mechanical “dry” disc brake pad assemblies and rotor assemblies.d. Hydraulic, air, and mechanical “dry” drum brake shoe assemblies and drum assemblies.e. Hydraulic, air, and mechanical brake “block” when intended for use on a. thru d. above except for those vehicles, padassemblies, and shoe assemblies specifically procured for military use and/or tested under ATPD-2354. It must benoted that such the US Government’s Military Services buys only assemblies and doesn’t normally use “brake block”and relined brake shoes/pads, therefore testing using separate brake “block” was specifically excluded fromATPD-2354 by the original authors.
